Technical Information Plastic Filler

Technical Information Plastic Filler

presto Putty for plastics is a 2-component black polyester putty as a mixture of a highly elastic, amino-pre-accelerated polyester resin with different mineral, environment-friendly fillers.To fill scratches and damages and to aftertreat bonded plastic parts.Through its thixotropy and softness, profiles and contours can easily be rebuilt.

Besides the very good adhesion on nearly all plastics, the putty can also be applied on carbody sheets and zinc coated sheets.

For preparation and finishing your filling job, we recommend our presto sand papers. We offer a wide assortment of fine and coarse papers for dry and wet sanding.

Quality and properties

  • Ease of working
  • High elasticity
  • Easy to sand
  • Very good adhesion
  • Free of asbestos and silicone
  • Pore-free
  • Resistant to weak acids and bases, propellants, solvents, water and de-icing salt

Physical and chemical data

  • Basis: polyester resin with mineral fillers
  • Colour: black
  • Smell: characteristic
  • Consistence: soft, thixotropic, pasty
  • Pot life / Working time at 20°C: approx. 7 - 8 minutes
  • Working temperature: min. 12°C
  • Drying time (at 20°C, 50% relative air humidity):
    can be sanded after approx. 30 - 40 minutes
  • Flash point:
    approx. 33°C (resin); not applicable for hardener
  • Density at 20°C:
    putty 1.89 g/cm³
    hardener 1.15 g/cm³
  • Addition of hardener: 2 - 4 % (optimal mixture 2,5 %)
  • Temperature resistance of the cured material: 120°C
  • Storage stability:
    18 months if appropriate storage provided (=10°-25°C, relative air humidity of max. 60%) in the unopened original container. Protect from direct sunlight, frost and humidity.
  • Packing:
    small ring tins; hardener: plastic tubes 

Environment and labelling

Environmentally sound: European Aerosols is committed to apply formulations without restricted or critical ingredients and to achieve best possible performance. The caps and packagings are made of recyclable material.

Disposal: Only the completely emptied cans should be put into the recycling skip or appropriate container for reclaimable refuse. Cans which are not empty should be disposed off as "special refuse".

Marking/Labelling: All products made by  European Aerosols comply with the actual labelling regulations according to Preparation Guideline 1999/45/EG. All aerosols correspond to TRGS 200  and TRG 300 as well as to aerosol guideline 75/324/EWG in the actually valid version.

Application

  • The object you wish to repair should be de-rusted, clean, dry, fat-free and sanded.
  • Take the requested portion of putty compound out of the can and mix it well with the corresponding quantity of hardener.
  • Apply the mixed material in the desired layer thickness.
  • Clean tools immediately after use, if necessary with a nitro thinner.
  • Do not return mixed material into the can.
  • After approx. 30-40 minutes the repaired spot can be drilled, sanded, sawed, rasped and painted.
  • The putty adheres to all customary hard plastics in the car, such as PP, PUR, ABS, PA, PVC.
  • Not suitable for weak plastics!
 

Order informations

 Color   Product   Bundle   Art.No. 
 presto SF Kunstst.Sp. 1000g   1 KG   443800 
 presto SF Kunstst.Sp. 250g   250 g   443732 

* kleuridentificatie niet mogelijk
De weergegeven kleuren wijken mogelijk af van de originele kleuren.
Om de productgegevens af te drukken, klik op "printing preview/further products".

Examples for use

Technical Information Plastic Filler
Technical Information Plastic Filler

Disclaimer of liability

This application-technological information is given to the best of our knowledge. The notes mentioned herein are, however, non-binding and do not exempt you from own tests to see whether the products supplied by us are suitable for your special application. The use and processing is beyond our control and therefore exclusively in the responsibility of the user. European Aerosols is let off the liability, unless the liability-based incident is caused by a fault incurred to European Aerosols.

As of March 08, 2016
This release replaces all eventually earlier issued versions.